MKR ZERO has an on-board SD connector with dedicated SPI interfaces (SPI1) that allows you to play with MUSIC files with no extra hardware! Watch out music makers, Arduino has released two libraries for your enjoyment: Arduino Sound library - a...

Waveshare 12915 - 250x122, 2.13inch E-Ink display HAT for Raspberry Pi, SPI interface This is an E-Ink display HAT for Raspberry Pi, 2.13inch, 250x122 resolution, with embedded controller, communicating via SPI interface, supports partial refresh...

Waveshare 14542 - Speaker Module for micro:bit, makes it become a music player This product is a mini buzzer expansion board based on micro:bit, which integrates the IC NS8002 bridge audio power amplifier, a high quality speaker, and a headphone...

The Servo Six board simplifies the process of connecting up to six servo motors to a Raspberry Pi or Arduino. Resources Datasheet (PDF) Instructions (PDF) Hi Res Images (Google File Share)

Operating Voltage : 5V(DC) Static Current: Less than 2mA. Output Signal: Electric frequency signal, high level 5V, low level 0V. Sensor Angle: Not more than 15 degrees Detection Distance: 2cm-450cm High Precision: Up to 0.3cm Input Trigger...

No more bulky DIN Rail cases for the Arduino Uno or Mega! The DINrPlate is a neat little slim line DIN Rail Mount for Arduino/Genuino Uno and Mega! It's formed of a single plate with mounting holes and strain relief for the USB and Barrel jack...

4pin Mini Voice Sound Sensor Module Microphone Sound module - LM393 Chip  This sensor emits a signal if the microphone of the sensor detects a noise. The sensitivity of the sensor can be adjusted by means of a controller...

This is a digital temperature and humidity sensor module that works with all of the Arduino micro-controllers. Because it is a digital sensor it only necessitates 3 connections, Vcc, GND, and a digital pin for data output. With this sensor you get two...

Operating Voltage: 5V With LED indicates relay status Control terminal, low level pull, high level relay release Great for DIY project

This is a digital Tap/Knock sensor on a small circuit board that is designed to work with all of the Arduino boards. It is easy to incorporate into any project requiring only a 5v supply, ground, and a digital input to measure the sensors readings (High...

This is an Arduino-comptabile microcontroller ATmega328 running at 16MHz with external resonator (0.5% tolerance) 0.8mm Thin PCB USB connection off board Supports auto-reset 5V regulator Max 150mA output Over current protected Weighs less than...

This is an Arduino Compatible Ultrasonic sensor, it can be used to measure the distance from the sensor to other objects around it. These types of sensors are used on robots for collision avoidance and guidance or as trip sensors for alarm systems or...

The Micro is an Arduino-compatible microcontroller board based on the ATmega32u4, developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHzcrystal...

Product Description The NodeMcu is an open-source development kit based on the popular chip ESP8266 (ESP-12E), using the Lua programming language, a development environment for applications that provide fast Wi-Fi connectivity. The ESP8266 is a...

This is a motor shield for an Arduino Uno that makes it easy for your Arduino to control various types of motors! All you need to do is attach this to your Uno, run wires from your motors to the respective terminal blocks, and supply some external power...

This is a very popular LCD for the Arduino or Freeduino board. It includes a 2×16 LCD display which is backlit in blue. It uses the I2C communications protocol so it is compatible with any Arduino or Raspberry Pi! Key Features: Supports I2C...

This is a very popular LCD Keypad shield for Arduino or Freeduino board. It includes a 2×16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Analog Pin 0 is used to read the pushbuttons. The...

Octopus TMP36 Temperature Sensor Brick for Arduino and micro:bit is a temperature sensor with low voltage and accurate celsius read. It can provide voltage output,which forms a linear relationship with celsius temperature. TMP36 do not need any external...

OCTOPUS Potentiometer is a simple linear sliding potentiometer electronic building block module which can be used as a resistor divider output, HID control panel, or in the electronic building block kit. News: All of the Octopus bricks support Scratch...

Octopus Electronic Bricks, you can use them to build electronics projects just as easily as piling bricks. By using Octopus electronic bricks, you can connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart...