Right Angle USB cable - A/MicroB This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0, but with a twist! Literally! Instead of the cable coming straight out from the connector, there's a right angle bend. We thought this might make a...

These three wire JST-SH to DuPont cables let you use the debug port of your Pimoroni Pico board for easy, solderless SWD programming. These cables are available with a choice of male or female DuPont (jumper wire) ends - you'll need the male version if...

These three wire JST-SH to DuPont cables let you use the debug port of your Pimoroni Pico board for easy, solderless SWD programming. These cables are available with a choice of male or female DuPont (jumper wire) ends - you'll need the male...

Waveshare 15817 - USB To RS232/485/TTL Interface Converter, Industrial Isolation This is an industrial USB to RS232/485/TTL isolated converter with original FT232RL inside. It features embedded protection circuits such as power isolation, ADI magnetical...

Multifunctional USB Power Meter - LCD Color Display - USB / Micro USB / USB-C A handy tool that measures voltage, current, power, charge time, and more for all of your USB A, Micro B, and USB C gadgets (phones, power banks, etc.....

A handy little cable that connects to the JST connector on the underside of HyperPixel 4.0, allowing you to use I2C devices with your Raspberry Pi at the same time as the display. Note: this cable can be used with older models of HyperPixel 4...

Waveshare 21358 - USB-C Adapter For NGFF M.2 SSD, USB3.2 Gen2 Type-C Note that this adapter is ONLY for SATA M.2 SSDs. NVMe IS NOT supported! Features M.2 NGFF Protocol Support High-speed Transfer USB-C Connector: Transforming Your M.2 SSD Into...

This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards. They will work where "thick pin"...

Want to use your new Official Raspberry Pi 7" Touchscreen Display but need to keep your GPIO pins free? This handy little cable is just what you need! We love the Raspberry Pi touchscreen but we hate to block up our GPIO! That's why we had these...

USB A-Male to USB Micro-B Cable - 3ftPerfect for micro:bit and some Arduino boards!

USB 2.0 TO MICRO USB CABLE - A TO MICRO B - 6" (15 CM) - BLACK Power your Raspberry Pi 3/Pico/Zero, Micro:bit, or any Micro-B USB devices with this mini cable. SPECIFICATIONS Connector A: USB Type-A (4 pin) USB 2.0 Connector B: USB Micro-B (5...

USB 2.0 to Micro USB Cable - A to Right Angle Micro B - 3FT (1m) - Black Power your Raspberry Pi 3/Zero or any Micro-B USB devices with this cable. Specifications Connector A: USB Type-A (4 pin) USB 2.0 Connector B: Right Angle...

USB 2.0 to Micro USB Cable - A to Right Angle Micro B - 1.5FT (45 cm) - Black Power your Raspberry Pi 3/Zero or any Micro-B USB devices with this cable. Specifications Connector A: USB Type-A (4 pin) USB 2.0 Connector B: Right Angle...

Connect Pi Zero and standard Raspberry Pi cables/cameras. The adaptor can be used to connect Pi Zero camera with integral (with 22-pin/0.5mm pitch) cable to full sized Raspberry Pi. Or with a 22 pin 0.5mm pitch cable you can connect up a Pi Zero to a...

USB 2.0 to Micro USB Cable - A to Right Angle Micro B - 6" (15 cm) - Black Power your Raspberry Pi 3/Pico/Zero, Micro:bit, or any Micro-B USB devices with this mini cable. Specifications Connector A: USB Type-A (4 pin) USB 2.0 Connector B:...

Power two devices from a single micro USB supply. Connects power from a single Micro USB connector to the Dual Female USB Type A connector. Micro USB data lines are connected to the lower USB port. Please Note: FOR USE ONLY WITH 5 VOLT supplies and...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab an HDMI ribbon cable, then swap and switch any of our HDMI adapters on each end using the flex cable clips...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab an HDMI ribbon cable, then swap and switch any of Adafruit's HDMI adapters on each end using the flex cable...

HDMI Cable, Gold Plated - 3ft

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based...