2X2 Pin, 2.54mm Double Row Female Straight Header $0.95 A 4-Way Riser perfect to use with the Raspberry Pi PoE HAT! Specifications Pitch: 2.54mm Gender of Connector: Female Number of Pins: 2 x 2 Pin Type of Row: Double-Row Body Orientation: Straight Add to Cart
On Sale! GPIO Stacking Header for Pi – Extra-long 2×20 Pins Adafruit $1.95 $2.95 Connect your own PCB to a Raspberry Pi and stack on top with this normal-height female header with extra long pins. The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra... Add to Cart
0.1″ 2×20-pin Strip Right Angle Female Header Adafruit $1.65 If we could eat headers we’d have them for breakfast, lunch, and dinner. But we can’t : ( So we’re making the best of it and selling them! This 2×20-pin strip, right-angle female header is a perfect companion piece... Add to Cart
Half-size 400-Pin DIY Breadboard, Clear $3.95 This is a cute half-size clear breadboard, good for small projects. It’s 2.2″ x 3.4″ (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the... Add to Cart
Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi – Mini Kit Adafruit $18.49 The Raspberry Pi is a wonderful little computer, but one thing it isn’t very good at is controlling DC Servo Motors – these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to... Add to Cart
FM90 DC Motor in Micro Servo Body $2.95 This tiny DC Motor in Micro Servo Body is an interesting motor – it’s the same size and shape as our micro servo (like the FS90, FS90R, SG92R) but it isn’t a servo. It’s more like a DC motor + plastic... Add to Cart
1-Channel Relay Module for Arduino & Raspberry Pi (Keyes) $3.45 Operating Voltage: 5V With LED indicates relay status Control terminal, low level pull, high level relay release Great for DIY project Add to Cart
SG90 180 Degrees 9G Micro Servo Motor Tower Pro $3.95 Weight : 9 g Size : 22 x 11.5 x 27 mm Operating Speed (4.8V no load): 0.12sec/60 degrees Stall Torque (4.8V): 17.5oz/in (1.2 kg/cm) Temperature Range: -30 to +60 Degree C Dead Band Width: 7usec Operating Voltage:3.0-7.2 Volts Add to Cart
Pi-EzConnect Terminal Block Breakout HAT Alchemy Power $19.95 With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all... Add to Cart
Pi-BB Bread Board for Raspberry Pi Alchemy Power $14.95 Pi-BB is a powered half-size breadboard ideal for Raspberry Pi™, and compatible with Arduino & other development boards. Use with a Raspberry Pi or standalone for prototyping work. 300 connection points make it convenient to attach any... READ MORE
PiZ-EzConnect HAT Kit for Pi Zero Alchemy Power $12.95 PiZ-EzConnect KIT allows you to customize and build your own GPIO connector for a Raspberry Pi or a Pi-clone (e.g. Asus Tinker, PiOrange etc.) All 40 pins used by the Raspberry Pi are exposed. Soldering is required. KIT... READ MORE
PiZ-EzConnect Terminal Block HAT for Pi Zero Alchemy Power $15.95 PiZ-EzConnect allows connection to any Raspberry Pi header pins via a terminal block. Like the Pi-EzConnect board, PiZ-EzConnect conforms to the Pi Zero dimensions, making this a nice, compact, easy to use and connect GPIO’s to a Pi... Add to Cart
Pi-BB-RPS, Bread Board With Redundant Power for Pi Alchemy Power $29.95 Pi-BB-RPS provides Redundant Power Supply capability. Second power is the micro-USB power. Power is switched seamlessly between these two sources. Priority is given to power source with higher power Voltage. DC 5V and 3.3V is generated on the board. The... Add to Cart
CamJam EduKit 2 – Sensors PiShop.us $11.45 Description The CamJam EduKit 2 features the following components all neatly packaged in a project tin: 1 x Breadboard 1 x Immersible temperature Sensor 1 x PIR Sensor 1 x LDR 1 x Active Buzzer 1 x Red 10mm LED 1 x Blue 10mm LED 1 x 4.7K... Add to Cart
CamJam EduKit 1 – Starter PiShop.us $7.75 Description The CamJam EduKit features the following components all neatly packaged in a project tin: A 400-point breadboard 3 LEDs (Red, Yellow and Green) A button A buzzer Resistors and jumper cables The kit is accompanied by a set of... Add to Cart
Tactile Button Switch (6mm) - 20 Pack Adafruit $2.45 Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They... Add to Cart
5x7cm DIY Prototype Paper PCB $0.75 Description: High quality general purpose PCB. Material: Single Side Copper PCB. Hole Dia: about 1mm. Hole pitch: standard 2.54mm. For point to point DIY soldering. Size:5cm x 7cm - 1.97inch x 2.76inch. Quantity: 1PC Package Included : 1 X PCB Board Add to Cart
Full sized breadboard – 830 points $4.95 This is a ‘full-size’ breadboard, 830 tie points. Good for small and medium projects. It’s 2.2″ x 7″ (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails... Add to Cart
Assembled Pi T-Cobbler Plus – GPIO Breakout for A+/B+/Pi2/Pi3/Zero $6.95 This is the assembled version of the Pi T-Cobbler Plus. It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2,Pi 3! Or just any Pi with 2x20 connector. The Raspberry Pi B+ and Pi 2 has landed on the Maker World like a 40-GPIO pinned,... READ MORE
RasClock – Raspberry Pi Real Time Clock Module $10.95 RasClock is a highly accurate real-time clock that fits on a Raspberry Pi and includes a battery backup. Now available to purchase! RasClock uses one of the following chips: NXP PCF2127AT NXP PCF2127T NXP PCF2129AT NXP PCF2129T All of these... Add to Cart
