Use this switched battery holder to power your Micro:bit or other device. Equipped with a JST-PH male connector.

The MI:power board for the BBC micro:bit brings real portability to your wearable projects. The stylish, lightweight PCB is designed to fit snugly against the BBC micro:bit and features a built in buzzer and 3V coin cell holder. When...

Add some colour to your next coding project with our new Halo board for the BBC micro:bit. The Halo has 24 ZIP LEDs, which are individually addressable full colour LEDs. This means that each LED can display a huge spectrum of colours, allowing amazing...

The SparkFun weather:bit is a fully loaded “carrier” board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional weather station. With the weather:bit you will have access to barometric pressure, relative humidity...

We love games! We love writing games, building games and, yes, even building game consoles. That’s where the SparkFun micro:arcade kit for the micro:bit comes in! The kit includes the gamer:bit carrier board, which gives you access to a number of pins in...

The SparkFun gator:bit is an all-in-one “carrier” board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you...

The SparkFun gamer:bit is a fun-filled “carrier” board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional game system. Designed in a similar form factor to the classic Nintendo NES controller, the gamer:bit is...

The MonkMakes Relay for micro:bit is a solid-state (no moving parts) relay that allows an output of a micro:bit to turn things on and off. A micro:bit can turn an LED on and off directly, but anything more powerful requires something like a relay or a...

Octopus TMP36 Temperature Sensor Brick for Arduino and micro:bit is a temperature sensor with low voltage and accurate celsius read. It can provide voltage output,which forms a linear relationship with celsius temperature. TMP36 do not need any external...

OCTOPUS Potentiometer is a simple linear sliding potentiometer electronic building block module which can be used as a resistor divider output, HID control panel, or in the electronic building block kit. News: All of the Octopus bricks support Scratch...

Octopus Electronic Bricks, you can use them to build electronics projects just as easily as piling bricks. By using Octopus electronic bricks, you can connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces...

Octopus Electronic Bricks, you can use them to build electronics projects just as easily as piling bricks. By using Octopus electronic bricks, you can connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces...

The Water Sensor Provides a variable analog reading depending on how wet/damp the sensor is. Good for plants or fingers. The black lead goes on GND, the red lead goes on 3v and the blue lead goes on whichever pin is being used in the program. This item...

A small submersible pump designed for Ph neutral, ambient temperature, non-sticky liquids, ie water. It has a transistor interface with current limiting resistor to the micro:bit output and needs ~6V power to run. The black lead goes on to GND, the green...

A transistor that will allow other items to be switched where the micro:bit would not be able to. Items such as motors, larger speakers, relays and so forth, up to 1A total load. A current limiting resistor is in the circuit to protect the micro:bit...

A very accurate temperature sensor using a calibrated chip called a TMP36GZ. It is accurate to ±1°C at +25°C. At this temperature it outputs 750mV. It changes by 10mV per °C. The black lead goes on GND, the red lead goes on 3v and the blue lead goes on...

A small microphone with amplifier & threshold setting. It can detect when sound reaches a certain level. It can not detect a particular frequency and there is no support in the micro:bit programming environment at present for it to analyse the...

A small motor that moves it’s output arm to a position depending on the signal sent to it with a reasonable degree of accuracy & repeatability. The brown lead with the black croc clip goes on to GND, the yellow lead goes on to the Pin 0, 1 or 2 that...

A Light Emitting Diode as an additional LED. It uses a high brightness low current LED and includes a current limiting resistor to protect the micro:bit’s output. The black lead goes on to GND and the green lead goes on to whichever Pin 0, 1 &...

A pushbutton on a lead for when you need another pushbutton or you want it away from your micro:bit One lead goes on 3v or GND and the other lead goes on 0, 1, or 2. For advanced applications it is feasible to connect two pins with the pushbutton. It...