The Finch is a robot for computer science education. Its design is the result of a four year study at Carnegie Mellon's CREATE lab. The Finch is designed to support an engaging introduction to the art of programming. It has support for over a dozen...

These are standard '130 size' DC hobby motors. They come with a wider operating range than most toy motors: from 4.5 to 9VDC instead of 1.5-4.5V. This range makes them perfect for controlling with an Adafruit Motor Shield, or with an Arduino where you...

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to...

Want to add more sensors or an extra tier to your DiddyBorg v2?  Our Multifunction Top Kit allows you to extend your robot to do even more :) This version is in Clear Acrylic! With the Multfunction Top Kit fitted DiddyBorg v2 can...

Our most popular Raspberry Pi robot kit DiddyBorg is back with faster motors and a newly designed chassis! Red Edition comes with six upgraded 28mm 590rpm metal geared motors. Red ones really do go faster! The idea remains the same, a 6 wheeled...

YetiBorg v2 is a great kit to get started with Raspberry Pi robotics. The YetiBorg v2 kit can be assembled into two different configurations so you can customize the robot to do what you want it to. Low profile If you are looking to build a speedy...

Our most popular Raspberry Pi robot kit DiddyBorg is back with faster motors and a newly designed chassis! The idea remains the same, a 6 wheeled high-torque robotics platform, but give everyone the ability to add lots of extra functionality and get...

The MonsterBorg can be programmed as a self-driving robot, used for education about self-driving systems, or raced around the garden as an RC off-roader. It also makes a great platform for hacking about with robots by adding extra sensors or servos. The...

A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor was specified to have a max current of 350mA so that it could be driven easily with an Adafruit...

This tiny DC Motor in Micro Servo Body is an interesting motor – it’s the same size and shape as our micro servo (like the FS90, FS90R, SG92R) but it isn’t a servo. It’s more like a DC motor + plastic...

The Kitronik :MOVE mini buggy kit for the BBC micro:bit provides a fun introduction to robotics. The :MOVE mini is a 2 wheeled robot that is suitable for autonomous operation, remote control projects via a Bluetooth application or being controlled...

Weight : 9 g Size : 22 x 11.5 x 27 mm Operating Speed (4.8V no load): 0.12sec/60 degrees Stall Torque (4.8V): 17.5oz/in (1.2 kg/cm) Temperature Range: -30 to +60 Degree C Dead Band Width: 7usec Operating Voltage:3.0-7.2 Volts  

Stepper motors are great motors for position control. They can be found in desktop printers, plotters, 3d printers, CNC milling machines, and anything else requiring precise position control. Steppers are a special segment of brushless motors. They are...

Pololu Socket to External Drivers converter board. It plugs into a Pololu stepper driver socket and re-routs the Step,Direction,Enable,Ground pins to the stepper motor ports connector. Forum discussion on external drivers for the Raspberry Pi CNC Hat:...

This version of the DRV8825 Stepper Motor Driver Carrier ships with 0.1″-pitch male header pins installed as shown in the main product picture, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. This...

This high-torque standard servo can rotate approximately 180 degrees (90 in each direction). You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with...

The Protoneer RPI CNC Board combines a real-time CNC controller (Micro-controller running GRBL) with a powerful credit card size computer - a Raspberry Pi! By connecting the two systems, the CNC board created an ecosystem where the Raspberry Pi...