Adafruit 387 - Super-bright 5mm IR LED - 940nm Infrared LEDs are used for remote controls (they’re the little LED in the part you point at your TV) and ‘night-vision’ cameras, and these little blue guys are high-powered ones! They are...

This is a 5V 4-Channel Relay interface board. Be able to control various appliances, and other equipment with large currents. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, etc.). Features 5V 4-Channel Relay interface...

With the Pi-EzConnect you can connect all sorts of electronics to a single Raspberry Pi  with no soldering or breadboarding! This HAT has screw-terminals for each pin on the Pi Header Key features: Solderless or soldered connections for all...

This is a 10 Pack of 10K Ω Resistors. 10k Ohm ±5%, 1/6W Through Hole Resistor Axial Flame Retardant Coating, Safety Carbon Film

This is a 10 Pack of 1K Ω Resistors. 1k Ohm ±5%, 1/4W Through Hole Resistor Axial Flame Retardant Coating, Safety Carbon Film

This is a 10 Pack of 330 Ω Resistors. 330 Ohm ±5%, 1/6W Through Hole Resistor Axial Carbon Film

This is a 10 Pack of 4.7K Ω Resistors. 4.7k Ohm ±5%, 1/4W Through Hole Resistor Axial Flame Retardant Coating, Safety Carbon Film

Add some colour to your next coding project with our new Halo board for the BBC micro:bit. The Halo has 24 ZIP LEDs, which are individually addressable full colour LEDs. This means that each LED can display a huge spectrum of colours, allowing...

The MonkMakes Relay for micro:bit is a solid-state (no moving parts) relay that allows an output of a micro:bit to turn things on and off. This relay can be used to switch low voltage devices such as light bulbs, a motor, a small heating element or even...

ElecFreaks Octopus:bit (Breakout Board For micro:bit) | EF03405 The Octopus:bit Micro:bit Breakout Board gives clear, instant access to all Micro:bit GPIO pins. A voltage-switch feature lets you toggle selected pins between 3.3 V and 5 V levels. Ideal...

Caution! The BBC micro:bit is NOT included. You can buy the BBC micro:bit here. Looking to do more with your BBC micro:bit? Unlock its potential with this pre-built version of Kitronik Edge Connector Breakout Board! This...

The Photoresistor Pack of 10 offers light-sensitive resistors for a wide range of projects. Each sensor changes resistance based on light levels, making it useful for light detection and automation. These are ideal for hobby electronics, DIY builds, and...

Need some really bright LEDs? We are big fans of these clear blue LEDs, in fact we use them exclusively in our kits. They are very bright and have about 20 degree LED beam. They go easily into a breadboard and will add that extra zing to your project...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They...

A passive buzzer emits a tone when a voltage is applied across it. It also requires a specific signal to generate a variety of tones. Specifications Rated Voltage: DC 5V; Working Voltage: 6-24VDC Resonance Frequency: 2.8 +/- 0.5KHz; Sound Pressure:...

The Super Bright Red 5 mm LED delivers a crisp, narrow beam of bright red light. With a 640 nm wavelength, 1.8–2.2 V forward voltage, and about 20 mA current draw, it produces around 1500 mcd brightness. Compact and clear-cased, this LED is ideal...

Product Name : Ultrasonic Sensor Module;Chip : US-100;Fit for : MCU Pins Number : 5;Working Voltage : 2.4-5.5V;Current : 2mA Detection Range : 2-450cm;Detection Accuracy : 0.3cm+1%;Working Temperature : -20- +70C Borad PCB Size : 45 x 20 x 1...

This is a 5V, 10A 2-Channel Relay interface board. It can be used to control various appliances, and other equipments with large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP,...

This is a 5V 8-Channel Relay interface board able to control various appliances, and other equipment with large currents. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino,etc.). Features 5V 8-Channel Relay interface board,...

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably...