other

A passive buzzer emits a tone when a voltage is applied across it. It also requires a specific signal to generate a variety of tones. Specifications Rated Voltage: DC 5V; Working Voltage:...

40PCS Dupont Wire Color Jumper Cable，2.54mm Female to Female For Arduino

Description: High quality general purpose PCB. Material: Single Side Copper PCB. Hole Dia: about 1mm. Hole pitch: standard 2.54mm. For point to point DIY soldering. Size:5cm x 7cm - 1.97inch x 2...

Continuous beep - Breadboard friendly!

Working voltage: DC5V-20V Quiescent Current: 65uA Level Output Voltage: High 3V / Low 0V Delaying time: 0.3~18s (adjustable) Blockade Time: 0.2s Trigger Method: L: unrepeatable trigger / H:...

If this is out of stock, please consider this alternative product. Specifications: Chip: DS18B20; Voltage: 3.0~5.5V Temperature range: -55'C~+125'C (-67'F~+257'F) Output wires: Red(VCC),...

This is a cute half-size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power...

The Zero Stem is a PCB shim that turns a Raspberry Pi Zero into a USB dongle. Once the shim is installed, your Raspberry Pi can be plugged directly into a computer or USB hub without any additional...

Brass standoff kits ideal for Raspberry Pi, Arduino, and other electronics. These are ideal for Alchemy Power products such as Pi-EzConnect, Pi-16ADC, Pi-BB, and Pi-UpTime...

Heatsink 1: Size: 14 x 14 x 6mm Baseboard thickness: 1.0mm Fin thickness: 0.7mm Fin number: 7 pieces Fin space width: 1.5mm Heatsink 2: Size: 9 x 9 x 4mm Baseboard thickness: 1.0mm Fin...

Details: Can be also used to space circuit boards, panels, doors or gears Also known as standoff separator Dimensions : Depth = 5mm Height = 18mm Width = 5mm Weight = 1.4g Thread size...

Please Note: The Raspberry Pi Zero is NOT included in this product! This camera cable is specifically designed to work with the Raspberry Pi Zero - Version 1.3! Just plug it into your Pi Zero's...

This USB to Micro USB Cable with switch is 1.5m long and is the perfect hard on/off power switch for your Raspberr yPi. This cable can be using in conjunction with a USB mains charger such...

A 50cm USB to Micro USB Cable.

Depending on the batch we received, this module can be DS3231 or DS3231M. The DS3231 is a low-cost, extremely accurate I2C realtime clock (RTC) with an integrated...

USB2.0 Interface for 480 Mbps high-speed transmission Supports Windows 7 Vista XP 2000 ME 98 or above Supports Mac OS 9.0 or above Reads only micro SD card

Note: For compatibility with Raspberry Pi boards, this hub must be set to USB 1.0 speed. To do so, type the following command in the terminal; sudo nano /boot/cmdline.txt and add the following line...

The Mini-HDMI Plug to Standard HDMI Jack Adapter for Pi Zero lets your Raspberry Pi Zero connect to a full-size HDMI cable. It converts the device’s mini-HDMI port into a standard HDMI jack,...

The USB OTG Host Cable – MicroB OTG male to A female lets you plug full-size USB devices (like keyboards, mice, flash drives) into devices with a Micro-B OTG port. It’s passive, so it...

A dual row of headers – break to fit. 2x20 pins that can be cut to any size. Dimensions: Upper pin length: 6.0mm Plastic height: 2.5mm Lower pin length: 3.0mm