This is a 170mm long 915MHz 50ohm antenna kit targeted for use with our LoRa and SubGHz products. The antenna can tilt and swivel making it easy to install it in various applications. The kit also...

The Challenger RP2040 SubGHz board is an Arduino/Circuitpython compatible Adafruit Feather format micro controller board based on the Raspberry Pico (RP2040) chip. This is a spin-off from our...

The Challenger RP2040 LoRa is an Arduino/Circuitpython compatible Adafruit Feather format micro controller board based on the Raspberry Pico (RP2040) chip. This is a spin-off from our Challenger...

Let your project know its place in the world with this tiny but ultra-sensitive global positioning breakout! This I2C breakout houses a PA1010D GPS receiver module with inbuilt ceramic antenna,...

Warning: this wire pack will NOT work with the new Navio2 Plus. Please get the Navio2 Plus wire pack instead. Includes 2x DF13 6-pin to 2.54 mm female jumpers for UART and ADC ports 1x DF13...

This module supports both Navio2 and Navio2 Plus boards. Supports LiPo batteries up to 6S Max current sensing: 60 A* Switching regulator output: 5.3 V 2.25 A 6-pos DF13 cable for connection to...

This antenna is NOT compatible with NEO-6T USB dongle. Benefits Superior multipath signal rejection Great out-of-band signal rejection Excellent signal-to-noise ratio Consistent response in...

Autopilot HAT for Raspberry Pi powered by ArduPilot and ROS Turn your Raspberry Pi® into a drone controller by using the might of sensors and controllers on board. Currently supported...

LoRa™ HAT, a low-power consumption data transmission module, comes with an onboard CH340 USB TO UART converter, Voltage Level Translator(74HC125V), E22-900T22S and E22-400T22S SMA antenna connector,...

Add both WiFi and Bluetooth capability to your computer super fast with this USB Bluetooth / WiFi Dongle! This little two-faced cutie is so versatile! Its WiFi half can be used to make Internet of...

External LTE-M Antenna Kit for use with the FiPy and GPy development boards. Specification Frequency: 703~803/2520~2620(MHz) Antenna size: 75 x 21 (mm) PCB 0.6

Meet our new Pygate case. It will fit your Pygate in perfectly. It’s a translucent smokey colour, made from a polycarbonate material. Pygate is an 8-channel LoRaWAN gateway. Connect your WiPy 3...

Raspberry Pi Dual-Band 5GHz / 2.4GHz USB Wi-Fi Adapter with Antenna If the on-board Wi-Fi on your Raspberry Pi isn't giving you enough range, this dual-band 2.4GHz/5GHz USB 2.0 Wi-Fi adapter is a...

Waveshare 17372 - 4G/3G/2G/GSM/GPRS/GNSS HAT For Raspberry Pi, Based On SIM7600G-H - SIM7600G-H 4G HAT The SIM7600G-H 4G HAT is a 4G/3G/2G communication and GNSS positioning module, which supports...

The Throwing Star LAN Tap is a passive Ethernet tap, requiring no power for operation. There are active methods of tapping Ethernet connections (e.g., a mirror port on a switch), but none can beat...

Give your Ultimate GPS V3 a boost with this external active antenna. This GPS antenna draws about 10mA and will give you an additional 28 dB of gain. It's got a 5 meter long cable so it will easily...

VK-162 USB GPS Navigation Module The VK-162 GPS Receiver is a low-cost high-sensitivity GPS Receiver + Internal Antenna with USB connector. It is a standalone GPS receiver providing a solution with...

Greater Scott Gadgets - YARD Stick One is a sub-1 GHz wireless test tool controlled by your computer. YARD Stick One (Yet Another Radio Dongle) from Great Scott Gadgets can transmit or receive...

The Throwing Star LAN Tap is a passive Ethernet tap, requiring no power for operation. Theory of Operation The Throwing Star LAN Tap is a passive Ethernet tap, requiring no power for operation...

WARNING: This adapter requires installation of a third-party driver. Although it is relatively simple, PLEASE READ THE INSTALLATION INSTRUCTIONS