8086 Consultancy

USB3 Power Switch - Logic Level DefaultTurn your USB3 devices on/off using a switch or Pi/Pico/Arduino/etc. The USB3 Power Switch is available in two models, Logic Level (LL) and Open Drain (OD)...

Assembled - PicoIO64 with soldered 2x20 headers and socket for a Pico/Pico2 [W] with headers.The PicoIO64 adds 64 3.3V I/O pins (5V tolerant) to the Raspberry Pi Pico using four 16-bit XRA1403 SPI...

The USB Switch/Multiplexer allows a USB device (or multiple devices if connected via a USB hub) to be switched between two hosts, or powered off. This newer 4-pin version adds a 3.3V output which can...

The 8086 USB-USB NULL Modem (UUNM) is a back-to-back USB to Serial converter using USB CDC Serial - meaning drivers are already built in to most modern operating systems (Linux/Windows 10/Mac OS...

The Pico Dongle Lite is a small micro USB plug to Type-A plug adaptor designed for use with the Pico H/W from Raspberry Pi but will be useful for many other jobs. Whilst there are many similar...

PicoADC16 for Raspberry Pi Pico [W] The PicoADC16 is a 16-port 10-bit ADC (Analog-to-digital converter) supporting up to 3.3 volts with screw terminals for easier usage. The PicoADC16 is a 16-port...

8086 Consultancy - Fan controller for Raspberry Pi - Horizontal 2.54mm (0.1")Raspberry Pi/Fan not included this is just a controller This is a small board with a load switch to allow a...

Handheld button/LED board designed for use with CircuitPython What is it? A multipurpose handheld device which could be used as a USB keyboard, keystroke replay, reacting to gestures, serial...

Connect Pi Zero and standard Raspberry Pi cables/cameras. The adaptor can be used to connect Pi Zero camera with integral (with 22-pin/0.5mm pitch) cable to full sized Raspberry Pi. Or with a 22...

Pi4, ClusterHAT, FanSHIM, etc. NOT included. Keep the 3.3v rail alive between reboots. When rebooting a Raspberry Pi 4 the 3.3 volt rail is reset which causes problems for some HATs. 3v3 Sustain...

Power two devices from a single micro USB supply. Connects power from a single Micro USB connector to the Dual Female USB Type A connector. Micro USB data lines are connected to the lower USB port...

FOR USE WITH GIANT BUTTERFLY PCB Hardware Kit [ OPTIONAL ] The hardware kit includes everything  you need to mount the Giant Butterfly PCB on your Raspberry Pi and then mount up to four HATs...

The adaptor allows the Raspberry Pi 4 to be used with a Pi USB-C power supply (or DC barrel jack) whilst allowing access to USB 2 OTG data over a separate USB-C connection (USB3 data is not...

What is it? APlusCam is designed in the shape of a Raspberry Pi HAT with mounting holes for a Raspberry Pi Camera and suction cups allowing the camera can look out through a window. The original...

The kit contains the following connector boards and pin headers. QtyTypeGender 2 Micro USB Male 2 Micro USB Female 2 USB Type-A Male 2 USB...

The ClusterCTRL Stack (controller and passive backplane) is a simple way to both power and control cooling for a stack of 5 Raspberry Pi. Controller Powered by 12-24V PSU. 20 pin header for...

The I2C multiplexer allows connecting multiple I2C devices with the same address onto a single I2C bus (PCB colour may vary). For each multiplexed output there are 4 pins - data ports SDAx, SCLx GND...

Allows four HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected, ID_SD and ID_SC (HAT EEPROM) have cuttable solder jumpers. For HAT/pHAT with an...

USB Serial Adaptor Plugs directly onto our Cluster HAT and MMC (SD) HAT to provide serial console access to the Raspberry Pi for quick access. Using jumper wires it can be used to access the serial...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC...