8086 Consultancy

Assembled - PicoIO64 with soldered 2x20 headers and socket for a Pico/Pico2 [W] with headers.The PicoIO64 adds 64 3.3V I/O pins (5V tolerant) to the Raspberry Pi Pico using four 16-bit XRA1403 SPI...

Power from each USB-C input (A/B) connector goes via a MOSFET "Ideal Diode" to the USB-C output connector. USB2 data from the USB-C port (A) is connected to the output USB-C connector (USB3 data is...

The Pico Dongle Lite is a small micro USB plug to Type-A plug adaptor designed for use with the Pico H/W from Raspberry Pi but will be useful for many other jobs. Whilst there are many similar...

PicoADC16 for Raspberry Pi Pico [W] The PicoADC16 is a 16-port 10-bit ADC (Analog-to-digital converter) supporting up to 3.3 volts with screw terminals for easier usage. The PicoADC16 is a 16-port...

8086 Consultancy - Fan controller for Raspberry Pi - Horizontal 2.54mm (0.1")Raspberry Pi/Fan not included this is just a controller This is a small board with a load switch to allow a...

Connect Pi Zero and standard Raspberry Pi cables/cameras. The adaptor can be used to connect Pi Zero camera with integral (with 22-pin/0.5mm pitch) cable to full sized Raspberry Pi. Or with a 22...

Pi4, ClusterHAT, FanSHIM, etc. NOT included. Keep the 3.3v rail alive between reboots. When rebooting a Raspberry Pi 4 the 3.3 volt rail is reset which causes problems for some HATs. 3v3 Sustain...

Convert your Pi Zero to a Micro USB dongle (no soldering required) Connect your Raspberry Pi Zero or Pi Zero W[H] directly to peripherals with a Micro USB port such as the Official Raspberry Pi...

FOR USE WITH GIANT BUTTERFLY PCB Hardware Kit [ OPTIONAL ] The hardware kit includes everything  you need to mount the Giant Butterfly PCB on your Raspberry Pi and then mount up to four HATs...

What is it? APlusCam is designed in the shape of a Raspberry Pi HAT with mounting holes for a Raspberry Pi Camera and suction cups allowing the camera can look out through a window. The original...

The adaptor allows the Raspberry Pi 4 to be used with a Pi Micro USB power supply (or DC barrel jack) whilst allowing access to the OTG USB. USB Type-A (data and power) <> USB Data (Micro USB)...

The ClusterCTRL Stack (controller and passive backplane) is a simple way to both power and control cooling for a stack of 5 Raspberry Pi. Controller Powered by 12-24V PSU. 20 pin header for...

This HAT disables WiFi on Raspberry Pi 3B and 3B+ The MMC HAT adds a second micro SD socket to your Raspberry Pi using the second SDIO interface. Please note that the MMC HAT is only officially...

The I2C multiplexer allows connecting multiple I2C devices with the same address onto a single I2C bus (PCB colour may vary). For each multiplexed output there are 4 pins - data ports SDAx, SCLx GND...

Allows four HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected, ID_SD and ID_SC (HAT EEPROM) have cuttable solder jumpers. For HAT/pHAT with an...

Caution! This product is NOT compatible with the new Raspberry Pi Zero W 2 Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC...

Dual Supply for Raspberry Pi (A+/B+/2B/3B/3B+) Power from each Micro USB connector goes via a MOSFET "Ideal Diode" which is then connected directly to the Micro USB socket on the Raspberry Pi. Data...

Connect your Raspberry Pi Zero or Pi Zero W directly to your computer for use as a USB Gadget device (USB Ethernet / Serial / Ethernet+Serial / etc.) or just for power. Works with all public...

The Raspberry Pi camera module comes with its own 30cm cable to connect to the Pi, but sometimes that’s simply not long enough. This lovely little board lets you add extension cables to your...