8086 Consultancy

8086 Consultancy - Fan controller for Raspberry Pi - Horizontal 2.54mm (0.1")Raspberry Pi/Fan not included this is just a controller This is a small board with a load switch to allow a...

Handheld button/LED board designed for use with CircuitPython What is it? A multipurpose handheld device which could be used as a USB keyboard, keystroke replay, reacting to gestures, serial...

Connect Pi Zero and standard Raspberry Pi cables/cameras. The adaptor can be used to connect Pi Zero camera with integral (with 22-pin/0.5mm pitch) cable to full sized Raspberry Pi. Or with a 22...

Pi4, ClusterHAT, FanSHIM, etc. NOT included. Keep the 3.3v rail alive between reboots. When rebooting a Raspberry Pi 4 the 3.3 volt rail is reset which causes problems for some HATs. 3v3 Sustain...

Convert your Pi Zero to a Micro USB dongle (no soldering required) Connect your Raspberry Pi Zero or Pi Zero W[H] directly to peripherals with a Micro USB port such as the Official Raspberry Pi...

Power two devices from a single micro USB supply. Connects power from a single Micro USB connector to the Dual Female USB Type A connector. Micro USB data lines are connected to the lower USB port...

FOR USE WITH GIANT BUTTERFLY PCB Hardware Kit [ OPTIONAL ] The hardware kit includes everything  you need to mount the Giant Butterfly PCB on your Raspberry Pi and then mount up to four HATs...

The adaptor allows the Raspberry Pi 4 to be used with a Pi USB-C power supply (or DC barrel jack) whilst allowing access to USB OTG data over a separate USB-C connection. USB Type-C (DATA POWER)...

What is it? APlusCam is designed in the shape of a Raspberry Pi HAT with mounting holes for a Raspberry Pi Camera and suction cups allowing the camera can look out through a window. The original...

The kit contains the following connector boards and pin headers. QtyTypeGender 2 Micro USB Male 2 Micro USB Female 2 USB Type-A Male 2 USB...

The adaptor allows the Raspberry Pi 4 to be used with a Pi Micro USB power supply (or DC barrel jack) whilst allowing access to the OTG USB. USB Type-A (data and power) <> USB Data (Micro USB)...

The ClusterCTRL Stack (controller and passive backplane) is a simple way to both power and control cooling for a stack of 5 Raspberry Pi. Controller Powered by 12-24V PSU. 20 pin header for...

This HAT disables WiFi on Raspberry Pi 3B and 3B+ The MMC HAT adds a second micro SD socket to your Raspberry Pi using the second SDIO interface. Please note that the MMC HAT is only supported on...

The I2C multiplexer allows connecting multiple I2C devices with the same address onto a single I2C bus (PCB colour may vary). For each multiplexed output there are 4 pins - data ports SDAx, SCLx GND...

Allows four HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected, ID_SD and ID_SC (HAT EEPROM) have cuttable solder jumpers. For HAT/pHAT with an...

Caution! This product is NOT compatible with the new Raspberry Pi Zero W 2 Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter...

Enables power to a USB device to be turned on/off via a USB power switch (MOSFET). Configuration Supplied with the PD (pull down) resistor set (Normally off). Connectors on top for GND / EN /...

USB Serial Adaptor Plugs directly onto our Cluster HAT and MMC (SD) HAT to provide serial console access to the Raspberry Pi for quick access. Using jumper wires it can be used to access the serial...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC...

Dual Supply for Raspberry Pi (A+/B+/2B/3B/3B+) Power from each Micro USB connector goes via a MOSFET "Ideal Diode" which is then connected directly to the Micro USB socket on the Raspberry Pi. Data...