Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins...

Adafruit 1554 - PCB Ruler v2 - 6" The first time you soldered up a surface mount component you may have been surprised "these are really small parts!" and there's dozens of different names too! QFN, TDFN, SOIC, SOP, J-Lead, what do...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they...

The easiest way to use breakouts with your Raspberry Pi. There's no soldering required, just pop up to three Pimoroni breakouts into the slots on Breakout Garden Mini and get started coding and creating. Grow your projects on Breakout Garden. It's ideal...

If you're going to be adding and removing wires to a project, these 2.54 pitch headers are an ideal way to make it easy and reliable. This box has a useful selection. Includes 2x male 2.54mm 2x20 header 10x male 2.54mm 1x20 header 4x male 2.54mm...

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: it's always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a...

A preposterous pile of peripherals on your Pi! Mix and match 3 HATs or 5 pHATs into a platter of functionality. Use pHAT Stack for specific setups and projects, or just as a handy way to use several HATs or pHATs at once. pHAT Stack is the big brother...

Mini PIR Motion Sensor – Breadboard Friendly with 3-Pin Header – Compact motion detection for projects PIR sensors are used to detect motion from pets/humanoids from about 5 meters away (possibly works on zombies, not guaranteed). This...

Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to your Pi Zero or pHAT. If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then...

A minimal RP2040 breakout board wrangled into a Pin Grid Array, with 8MB flash and a maximal dash of retraux style. PGA2040 is a compact RP2040 breakout intended for the most svelte and embeddable of projects. It contains only the components necessary...

Raspberry Pi Pico is not included A conveniently sized, labelled proto-board add-on for your Raspberry Pi Pico, perfect for permanently attaching your custom circuits! With a 6x20 grid of 2.54mm spaced holes for easy soldering and labelled Pico pins so...

This potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own. We like this one because...

These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped...

This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards. They will work where "thick pin"...

These are our favorite trimpots, perfect for breadboarding and prototyping. They have a long grippy adjustment knob and with 0.1" spacing they plug into breadboards or perfboards with ease. This is the same pot that comes with our character LCDs and...

A demo board for exploring the digital video and audio capabilities of Raspberry Pi Pico, with HDMI connector, SD card slot, line level I2S audio and buttons. Raspberry Pi Pico is not included. Your Pico will need to have pin headers soldered to it...

Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to your Pi Zero or pHAT. Raspberry Pi Zero not included If your soldering isn't quite up to scratch, or you just don't...

Eight super-bright RGB LED indicators that are ideal for adding visual notifications to your Raspberry Pi without breaking the bank! Inspired by Alex Ellis' work with his Raspberry Pi Zero Docker Cluster, Pimoroni developed these boards for...

Mini Black HAT Hack3r – Fully AssembledNeed to detach or debug your HAT? Then the Mini Black HAT Hack3r is for you! A nifty little tool that lets you access all of the GPIO pins while also running a HAT. Ideal for debugging your HAT projects or...

Transform your Raspberry Pi Pico into a electronic adventure playground packed with physical computing goodies including an LCD screen, motor drivers, a mini breadboard, and much more! Pico Explorer lets you play with circuits, build science...