Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You...

Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly...

Finally Adafruit gets their very own super sweet sixteen... 16 millimeters that is! The Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories...

If you're looking for the most compact li'l color display for a Raspberry Pi B+, Pi 2, & Pi 3 (most likely a Pi Zero) project, this might be just the thing you...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on...

PIR sensors are used to detect motion from pets/humanoids from about 5 meters away (possibly works on zombies, not guaranteed). This sensor is much smaller than most PIR modules, which makes it great...

How many bags and pockets does an OTG (On The Go) maker need to carry their electronics when away from their desk? The world may never know. We get serious satisfaction when things fit into other...

This potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose...

These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size...

This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into...

These are our favorite trimpots, perfect for breadboarding and prototyping. They have a long grippy adjustment knob and with 0.1" spacing they plug into breadboards or perfboards with ease. This is...

This is a basic, classic Adafruit Raspberry Pi Camera Board Enclosure with a black base and a clear top. The case is as minimal as it gets, coming in just two pieces of polycarbonate...

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The female header part has extra spaces to make it 23.5...

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output) pins and for those of us who like to hack...

Hey Mr. DJ! Turn up that Raspberry Pi mix to the max with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi. (It's not big enough to be an official HAT, so Adafruit called it a...

This is the assembled version of the Pi T-Cobbler Plus.  It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi with 2x20 connector)The Raspberry Pi B+ and...

Connect this to that without soldering using these handy mini alligator clip test leads. 15" cables with alligator clip on each end, color coded. You get 12 pieces in 6 colors. Strong and grippy,...

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) or Raspberry Pi Display for a different size. Works great, just carefully...

Connect your own PCB to a Raspberry Pi with this normal-height female header.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This...

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.5 mm tall: when placed on your Pi, a PCB will clear the Ethernet and...