MonkMakes SKU00105 - Pico Controller A 4-channel low-voltage Solid State Relay controller designed for the Raspberry Pi Pico. Ideal for projects involving: Model railroads RV / caravan 12V lighting projects Aquarium and greenhouse...

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins...

Adafruit 1554 - PCB Ruler v2 - 6" The first time you soldered up a surface mount component you may have been surprised "these are really small parts!" and there's dozens of different names too! QFN, TDFN, SOIC, SOP, J-Lead, what do...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is pressed they...

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: it's always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a...

Mini PIR Motion Sensor – Breadboard Friendly with 3-Pin Header – Compact motion detection for projects PIR sensors are used to detect motion from pets/humanoids from about 5 meters away (possibly works on zombies, not guaranteed). This...

Prototyping board designed for the Raspberry Pi Pico with the Pico pinout marked on the PCB. If you liked our breadboard for Pico and are ready to take your prototype to solder, you will love this board. This prototyping board is inspired by the...

This potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own. We like this one because...

These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped...

This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards. They will work where "thick pin"...

These are our favorite trimpots, perfect for breadboarding and prototyping. They have a long grippy adjustment knob and with 0.1" spacing they plug into breadboards or perfboards with ease. This is the same pot that comes with our character LCDs and...

Stack multiple plates, breakouts etc onto your Raspberry Pi Model B+ with this custom-made extra-tall and extra-long 2x20 female header. The female header part has extra spaces to make it 23.5 mm tall: when placed on your Pi, a PCB will clear the...

Color Coded Header for Raspberry Pi - Easy Pin Identification The Color Coded Header for Raspberry Pi Zero and Zero W makes GPIO pinouts easy to follow. Each of the 40 pins is marked with a color for fast identification. Red is 5V, yellow is 3V, black...

This is the assembled version of the Pi T-Cobbler Plus.  It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi with 2x20 connector)The Raspberry Pi B+ and Pi 2 has landed on the Maker World like a 40-GPIO...

Connect this to that without soldering using these handy mini alligator clip test leads. 15" cables with alligator clip on each end, color coded. You get 12 pieces in 6 colors. Strong and grippy, these always come in handy! We often use these in...

The Squid Combo Pack comprises a Raspberry Squid RGB LED, two Squid buttons and a Raspberry leaf to help you identify the GPIO pins. A bright RGB (Red, Green, Blue) LED with built-in resistors and female header leads that can just plug directly into the...

The Squid Button is a momentary action push switch with trailing leads that end in female header sockets that will fit over GPIO pins on a Raspberry Pi, Node MCU or Raspberry Pi Pico. To reduce the chance of accidental short-circuits when using the...

Bright RGB LED with built-in resistors Female header leads Plug directly into the GPIO pins of a Raspberry Pi The Monk Makes Squid RGB LED for Raspberry Pi is a bright RGB (Red, Green, Blue) LED with built-in resistors and female header...

This kit includes 2 servo motors and a Monk Makes ServoSix interface board for use with Raspberry Pi. It also includes a Raspberry Leaf GPIO template, a bunch of 10 female-to-female header pins and a 4xAA battery box Resources Instructions (PDF) Hi...

MONK MAKES - PROJECT BOX 1 FOR RASPBERRY PI | SKU00080 The MonkMakes Project Box 1 for Raspberry Pi is a complete electronics starter kit designed for easy hands-on learning. It replaces the original Electronic Starter Kit with updated...