Categories - PiShop.us

Sub Categories

Male to Female Jumper Cable x 40 (20cm)

$2.95

Handy for making wire harnesses or jumpering between headers on PCB's These premium jumper wires are 20cm long and come in a 'strip' of 40 0.1" male header contacts on one end and 0.1" female header contacts on the other Fit cleanly next to each other on...

Add to Cart

Active Buzzer - 5V

$0.99

Continuous beep - Breadboard friendly!

Add to Cart

Photoresistor, Light Dependent Resistor (LDR), GL5549

$0.95

Light Sensitive Resistor GL5549

Add to Cart

HC-SR501 Pyroelectric Infrared PIR Motion Sensor Detector Module

$3.95

Working voltage: DC5V-20V Quiescent Current: 65uA Level Output Voltage: High 3V / Low 0V Delaying time: 0.3~18s (adjustable) Blockade Time: 0.2s Trigger Method: L: unrepeatable trigger / H: repeatable trigger Detecting Range: 7m, less than 120...

Add to Cart

Waterproof DS18b20 Temperature Probe

$8.95

If this is out of stock, please consider this alternative product. Specifications: Chip: DS18B20; Voltage: 3.0~5.5V Temperature range: -55'C~+125'C (-67'F~+257'F) Output wires: Red(VCC), Yellow (DATA), Black(GND)

Add to Cart

Half-size 400-Pin DIY Breadboard, White

$5.45

This is a cute half-size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the breadboard as thin as 1.4"...

Add to Cart

Mini Remote Control

$3.95 $4.95

This little remote control would be handy for controlling a robot or other project from across the room. It has 21 buttons and a layout we thought was handy: directional buttons and number entry buttons. The remote uses the NEC encoding type and sends...

Add to Cart

USB BitScope 10

$294.95

BS10U really is tiny, but don't let the size fool you because it's a full feature mixed signal oscilloscope and test system not just another little logic analyzer (read full details). BS10U is USB powered and user programmable. It includes a set of ten...

Notify Me

BitScope Blade Uno PI

$39.95 $49.95

Uno Pi is a BitScope Blade designed to power and mount one Raspberry Pi and optional HAT. Uno Pi can also power and mount the Raspberry Pi Display. It's perfect for building industrial strength stand-alone physical computing solutions...

Add to Cart

BitScope Blade Duo Pi

$49.95 $59.95

Duo Pi is a BitScope Blade which can power and mount a pair of Raspberry Pi. It can also be used to power and mount the Raspberry Pi Display. It's perfect for building small dual processing redundant servers or stand-alone client/server...

Notify Me

BitScope Blade Quattro Pi - EOL

$69.95

This model of Quattro Pi is not fully compatible with the new Pi 4 boards due to power requirements. The Uno, Duo, and Blade Rack 40 are Pi 4 compatible, and and new version of the Quattro will soon support Pi 4. Quattro Pi is a BitScope...

Notify Me

Bitscope Micro PC Based Oscilloscope, 2+16CH, 20MHZ, 40MSPS

$129.95 $144.95

Bandwidth: 20MHz Input Impedance: 1Mohm Kit Contents: One Set of 10 Test Leads with Grabber Clips, Pair of Color Coded Analog Shorting Plugs, Connection Key Card Plug Type: USB Product Range: BITSCOPE - BS Series SVHC: To Be Advised Sampling...

Notify Me

Socket To External Driver Conversion Board

$3.95 $4.95

Socket to External Drivers converter board. It plugs into a Pololu stepper driver socket and re-routs the Step,Direction,Enable,Ground pins to the stepper motor ports connector. Forum discussion on external drivers for the Raspberry Pi CNC Hat: Using...

Add to Cart

DRV8825 Stepper Motor Driver Carrier, High Current

$7.95

This version of the DRV8825 Stepper Motor Driver Carrier ships with 0.1″-pitch male header pins installed as shown in the main product picture, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. This...

Notify Me

Raspberry Pi GPIO Kit

$12.95 $19.95

This kit has been discontinued, but is replaced by the following two separate kits: CamJam EduKit 1 – Starter CamJam EduKit 2 – Sensors The contents of the GPIO kit and CamJam 1+2 are identical.

Notify Me

Pi Zero USB Stem

$6.95

The Zero Stem is a PCB shim that turns a Raspberry Pi Zero into a USB dongle. Once the shim is installed, your Raspberry Pi can be plugged directly into a computer or USB hub without any additional cables or power supplies. The Zero Stem is compatible...

Add to Cart

Camera Cable Joiner/Extender for Raspberry Pi

$3.50

The Raspberry Pi camera module comes with its own 30cm cable to connect to the Pi, but sometimes that’s simply not long enough. This lovely little board lets you add extension cables to your existing camera cable, giving you as much range as...

Add to Cart

Acrylic case for MiniBoss

$7.95 $14.95

Please note that due to supply shortages the acyrlic case stock for this product is now solid black instead of transparent black as shown in the product images. Acrylic Case for miniBOSS For RPi Zero! IMPORTANT - Each acrylic case piece is covered...

Notify Me

Pimoroni Picade - BYO Screen

$124.95 $154.95

Right from our attic, the legendary Pimoroni Picade - BYO Screen, Brand NEW, sealed in its packaging - ONLY COMPATIBLE WITH RPi 3 or RPi 3B+ THIS KIT CONTAINS NO SCREEN. GO HERE FOR THE KIT WITH 8" SCREEN. The Picade comes in kit form...

Add to Cart

PiTFT Plus Pibow Case Only (for Pi 2, 3B, 3B+)

$19.95

Support and protect your PiTFT+ and Raspberry Pi with this stylish and unique case! Please note: if using with the 480×320 3.5″ PiTFT+ you will need to remove the mounting holes from the side of the PiTFT board (they’re designed to...

Notify Me