8086 Consultancy - USB-C/PWR Splitter, no Barrel The adaptor allows the Raspberry Pi 4/5 to be used with a Pi USB-C power supply whilst allowing access to USB 2 OTG data over a separate USB-C connection (USB3 data is not connected/passed through). USB...

Share a USB 3 device between two hosts or switch between two devices on one host. The bidirectional USB 3 Mux allows either a single USB device (or multiple devices when using a USB hub) to be switched between two USB hosts (computer) or using its...

USB3 Power Switch - Logic Level DefaultTurn your USB3 devices on/off using a switch or Pi/Pico/Arduino/etc. The USB3 Power Switch is available in two models, Logic Level (LL) and Open Drain (OD). You can switch between either model by altering the...

The USB Switch/Multiplexer allows a USB device (or multiple devices if connected via a USB hub) to be switched between two hosts, or powered off. This newer 4-pin version adds a 3.3V output which can be used to toggle the state using switches without the...

The 8086 USB-USB NULL Modem (UUNM) is a back-to-back USB to Serial converter using USB CDC Serial - meaning drivers are already built in to most modern operating systems (Linux/Windows 10/Mac OS X/Android) so you can just plug n' play! Users The...

Power from each USB-C input (A/B) connector goes via a MOSFET "Ideal Diode" to the USB-C output connector. USB2 data from the USB-C port (A) is connected to the output USB-C connector (USB3 data is not connected/passed through). The ideal diode...

Connect Pi Zero and standard Raspberry Pi cables/cameras. The adaptor can be used to connect Pi Zero camera with integral (with 22-pin/0.5mm pitch) cable to full sized Raspberry Pi. Or with a 22 pin 0.5mm pitch cable you can connect up a Pi Zero to a...

Power two devices from a single micro USB supply. Connects power from a single Micro USB connector to the Dual Female USB Type A connector. Micro USB data lines are connected to the lower USB port. Please Note: FOR USE ONLY WITH 5 VOLT supplies and...

The adaptor allows the Raspberry Pi 4 to be used with a Pi USB-C power supply (or DC barrel jack) whilst allowing access to USB 2 OTG data over a separate USB-C connection (USB3 data is not connected/passed through). USB Type-C (DATA POWER) <> USB...

The kit contains the following connector boards and pin headers. QtyTypeGender 2 Micro USB Male 2 Micro USB Female 2 USB Type-A Male 2 USB Type-A Female 4 - 6way long pin header Of the 6 pins on the...

The adaptor allows the Raspberry Pi 4 to be used with a Pi Micro USB power supply (or DC barrel jack) whilst allowing access to the OTG USB. USB Type-A (data and power) <> USB Data (Micro USB) and Power (Micro USB/Barrel jack). USB Type...

Caution! This product is NOT compatible with the new Raspberry Pi Zero W 2 Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter can still be soldered to the GPIO header). The...

Enables power to a USB device to be turned on/off via a USB power switch (MOSFET). Configuration Supplied with the PD (pull down) resistor set (Normally off). Connectors on top for GND / EN / 5V When the EN pin is connected to >2V (5V max) power...

USB Serial Adaptor Plugs directly onto our Cluster HAT and MMC (SD) HAT to provide serial console access to the Raspberry Pi for quick access. Using jumper wires it can be used to access the serial on a Raspberry Pi and for Arduino programming (using...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC drivers on most modern operating systems (Win10/Linux/Mac OS...