A rechargeable battery and acrylic case kit for your micro:bit. The Charger for micro:bit automatically charges while you are connected to USB. Make your micro:bits mobile without having to continually hunt for AAA batteries. Resources Datasheet...

The Terminal Breakout board for the BBC microbit does exactly what it says on the tin. It breaks out all of the signal and power pins on the microbit to user friendly terminal blocks. No more untangling M/M or M/F jumper cables from the hastily tidied...

This is a colorful strip based on WS2812B beads, it can display the color RGB and support multiple cascades at the same time. Characteristics Standard 3-pin GVS ports are easy to plug. Both ends are equipped with a connector and it supports multiple...

The Water Sensor Provides a variable analog reading depending on how wet/damp the sensor is. Good for plants or fingers. The black lead goes on GND, the red lead goes on 3v and the blue lead goes on whichever pin is being used in the program. This...

Click Me to Download the Instructions for this kit. The Servo Kit for micro:bit makes it easy to connect up three servomotors from your micro:bit. Not only that, but the kit also comes with three servomotors and a battery box. Just add a micro:bit and...

The MonkMakes Relay for micro:bit is a solid-state (no moving parts) relay that allows an output of a micro:bit to turn things on and off. This relay can be used to switch low voltage devices such as light bulbs, a motor, a small heating element or even...

With the Kitronik Compact Robotics Board, the BBC micro:bit can be used to drive 4 motors (or 2 stepper motors) and 8 servos. Coupled with 17 other I/O expansion points, this means the BBC micro:bit can very easily become the core of a whole variety of...

The STOP:bit for the BBC micro:bit is the ultimate upgrade for traffic light/pedestrian crossing projects. Not only does it make coding the project a breeze, but the board is also supplied pre-assembled so you don't even need to fire up the soldering...

Official micro:bit branded USB cables that allow you to power and transfer data to your micro:bit. High quality construction with PVC cable sleeve and embossed logos. USB 2.0 data transfer rates up to 480Mb/s USB A Plug to USB Micro B Plug 0.3m...

The MonkMakes Power for micro:bit opens up lots of ways of powering your micro:bit. This tiny board has a standard DC barrel jack socket at one end and provides a regulated 3.3V output that you can use to power your micro:bit using the JST battery...

Waveshare 14542 - Speaker Module for micro:bit, makes it become a music player This product is a mini buzzer expansion board based on micro:bit, which integrates the IC NS8002 bridge audio power amplifier, a high quality speaker, and a headphone...

A very accurate temperature sensor using a calibrated chip called a TMP36GZ. It is accurate to ±1°C at +25°C. At this temperature it outputs 750mV. It changes by 10mV per °C. The black lead goes on GND, the red lead...

This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this connector's...

Plug a servo meter with 5.4mm (0.1 inch) header socket in, and connect croc/alligator clips to the rings, so that you can easily connect a servomotor to a ring-based microcontroller, such as the BBC micro:bit, Adafruit Circuit Playground Express or...

The USB A-Male to USB Micro-B Cable - 6 inches is a compact link between standard USB A ports and Micro-USB devices. At just 15 cm long, it keeps setups neat with less cable clutter. Perfect for powering or programming boards that use Micro-USB,...

A type of buzzer – it has to be driven by a pulsed output. It’s tuned for around 2kHz when it will be at its loudest but will produce a tone across a wide range of frequencies. In the Block Editor, the black lead goes on to GND and the blue...

Sense the world around you with enviro:bit! It's loaded with sensors for air and weather, colour and light, and sound, and slots right onto your micro:bit. Just slot in your micro:bit, then code enviro:bit with the block-based Microsoft...

The MonkMakes RGB LED for micro:bit can be used to make any colour by controlling the red green and blue levels. Handily mounted on a PCB it connects to the micro:bit using alligator clips. Resources Datasheet (PDF) Instructions (PDF) Hi Res Images...

A simple buzzer with transistor that can be powered by the micro:bit. Costs more than a headphone adapter but far less than the mini-speaker – its best use is to act as a sounder for an alarm or similar.

Description A small version of the PIR that is used in a typical burglar alarm. It triggers when a warm body passes in front of the detector. It has some range / sensitivity setting capability and the duration of the output can be set. The black lead...